draw tite gooseneck hitch installation instructions

bradyfleury27505 July 02, 2022 draw , instructions , tite , wallpaper Comment

Used when installing a gooseneck hitch on 2007 and new Chevrolet and GMC trucks with factory installed brake controller. General instructions for fabricated support structures.

Toptow Trailer Hitch Extender Adapter With 6 Inch Riser Drop 2 Receiver 2 In Ebay In 2022 Trailer Hitch Cars Trucks Ebay

Since 1946 Draw-Tite has always strived to provide the right trailer towing system for each application.

. Mark and drill a 14 inch hole 44-916 inches short long box from the rear of the bed and centered between the wheel wells. ¾Periodically re-torque all the hitch fasteners. ¾Check ball hitch coupler safety.

The Draw-Tite Fold Down Gooseneck Hitch Installation Template part 6425 is listed as an essential tool when installing a Draw-Tite Reese and Hidden Hitch Fold Down Gooseneck Hitch like part 8339-4437 for your 2006 ford F-150. Install the hitch frame brackets by aligning the rearward holes in the brackets with the carriage bolts and install the 12 flat washer lock washers and hex nuts. Free shipping on orders over 99.

Installation Instructions 94609470 Hide-A-Goose Installation 1. Using a hole saw enlarge the pilot to the final diameter hole size. Draw-Tite Trailer Hitches Towing Accessories.

58318 Details In Stock - Ready to ship today. Raise truck box pretty torn up the draw tite gooseneck hitch installation instructions for treating or in the inside. The ball is stored upside down in the hitch when not used with a magnetic cover to keep dirt and debris out.

Move the handle toward the ball and then push it forward in the Z-slot to lock the handle into a closed position. Even though it is not required it will remove the guesswork when installing a gooseneck in the bed of your truck. Give this installation instruction to vehicle owner after installation is complete.

When tightened shank must protrude beyond bottom of nut. Hitch Balls and all friction points should be greased on a regular basis. This is why we offer as many as ten different trailer hitches for a single vehicle.

This adapter is fully locked before being posted or. From underneath the vehicle raise the gooseneck center section 1 up to the bottom side of the rails as shown and route the carriage bolts previously installed in the rails page 3 fig. Installation kit lets you install your gooseneck trailer hitch in the bed of your truck Designed for use with Draw-Tite Hide-A-Goose Remov-a-Ball and Fold-Down gooseneck hitches Bolt-on application - no welding required Included spacer shims keep truck-bed corrugation from collapsing Powder coated steel is durable and corrosion resistant.

8 hex nut 3. IF TOWING PRODUCTS MANUFACTURED RAIL KITS ARE NOT USED THIS PRODUCT BECOMES A GENERAL APPLICATION PRODUCT. Michael H Ask The Experts a Question.

Cover the slot with the magnetic cover provided. Place 58 GR8 carriage bolts from the Hide-A-Goose hitch fastener kit into the slots on the cross members from the top pointing towards the ground see Figure 1. Gross trailer weight rating and ball diameter are marked on DRAW-TITE balls.

Orient the through hole in the ball so it lines up with the sliding pin. I have included a link to the installation instructions for gooseneck trailer hitch 9467 to the right for you. GOOSENECK MOUNTING KIT Ford F-450 Will not fit Cab-on-Chassis vehicles ¾Always make sure the ball is fully locked before towing.

Fully welded Chevrolet Trax trailer hitch is strong and durable. Lower the spare tire to make installation of the cross members easier. 2 through the 4 outside holes in the center section and secure using 4 58 dia.

The combination of an e-coat base and a powder coat finish provides excellent rust protection. Shop for Draw-Tite Trailer Hitch 4193 with confidence at AutoZonecom Parts are never part from what. Many of the videos in this gallery are centered on our products and are a compilation of installation instruction and comparison information.

Activator Installation Instructions and Manual Part 5100 Activator II Installation Instructions and Manual Part 5500 New. ¾This rail kit can be used with a 9460 or 9470 head only. Draw-Tites Tested Tough guarantee ensures that this hitch exceeds industry standards.

GOOSENECK MOUNTING KIT ChevroletGMC 25003500 Heavy Duty Short Long Bed 94659475 HIDE-A-GOOSE HITCH INSTALLATION Hide-A-Goose Only Drilled hole in bed location see step 5. Loosely install the 58-11 hex nuts and conical toothed washers onto the threaded studs on the ends of the hitch cross members see Figure 7. Refer to the 94659475 Hide-A-Goose hitch instruction sheet for hole size.

Hide-A-Goose Installation Instructions 1. Loosely hang the drivers side and passengers side hitch side brackets by attaching the 58 hardware to the threaded studs. Gooseneck Installation Kit Draw-Tite Part.

Gooseneck Hitch are included as part of the Towing Products Rail Kit installation instructions. Whether its weight capacity ease of installation appearance or other factors that are important to you we aim to exceed your expectations. In this video we show you some tips for attaching your DrawTite Receiver HitchShop Trailer Hitches.

Brake Control Hard Wire Instructions OEM Brake Adapter Instructions Towing Trailer Hitches Front Mount Trailer Hitches Fifth Wheel Trailer Hitches. 9468 Draw-Tite Hide-A-Goose Underbed Gooseneck Trailer Hitch - 30000 lbs 4494 Draw-Tite Custom Installation Rails for Gooseneck Trailer Hitches Installation Details This Product Fits The Following. This will prevent buildup that could cause the ball to seize up in the hitch.

When installing the 94659475 Hide-A-Goose hitch a hole must be drilled in the bed of the truck. This cover prevents dirt and debris from getting into the ball hole. With the proper tools a buddy or two the installation should not be all that difficult.

Conical washer 2 and 4 58-11 Gr. ¾Keep the ball and ball sleeve well lubricated. Install the 58 X 300 carriage bolts through the hitch side brackets.

Step 2 Figure 4. 2021 Chevrolet Trax - Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2. Installation Instructions and Manuals.

This bracket kit relocates the br. This will allow the hitch ball to be installed into the tube. Hole to the final diameter hole size.

A 3-12 hole in the truck bed is required for installation and operation. Trailer Couplers The coupler socket should be smooth clean and lightly lubricated. Springs Front and slide Draw-Tite Trailer Hitch Installed Note Tires and.

Short Box 44-12 inches Long Box 49-38 inches. The hitch does come with all of the hardware for installation. Under-Bed Gooseneck This product is designed to mount under the truck bed for use with a gooseneck trailer.

Draw-Tite Video Library We live in a visual world and one of the best ways to convey a message today is through video.

Draw Tite 8339 Fold Down Gooseneck Hitch Head 25 000 Lbs Capacity